DK - 160 counter parts

Product principle:

Automatic SMD parts counter,On the principle of the photoelectric sensor,Using parts loaded with guide hole and parts,Through special processing chip and large scale integrated circuit processing,Achieve zero error,Accurate determination ofSMDNumber of parts,Can realize quick and easy counting,isSMTMaterial management efficient auxiliary equipment.

Product features:

Automatic calculation part number,Convenient point of material and the whole operation is simple, unique design to prevent strip off material with less damage to the minimum, direction, all can count, presetting quantity, precise calculation quantity, zero error.Can be mounted to the scanner and the bar code printer, convenient operation management.

Product specifications:

Power source:AC220/110，50HZ，25W

Count range:-99999~99999PCS

Installation dimensions:L470*W300*H180mm

Weight:10KG

Product application:

SMD materials can use belt type parts

Strip wheel diameter: any size all can use

Strip interval (PITCH) :2，4，8，10，12，16，24，32，44，56mm

Strip WIDTH (WIDTH) :8，12，16，24，32，44，56mm

Instructions:

A, function key details:

0-9 number keys

Confirm key (enter)

ENG/select

The left key

The right key

Stop key /Reset button

Print button

PITCH key

Second, the boot display

PITCH: xx mm

SET NO A COUNT

00000 00000

1.Modify the spacing

Xx for the current Settings of spacing press 'PITCH' key xx will flash, flash 'PITCH' release button and then press the xx will change and continue to shine In the 02-04-08-02-04-08-24 to 28-32-36-40-44-48-52-56 each time you press the change a switch in turn.Directly input the number keys when flashing needless to press 'PITCH' as for 02 to switch to the 48 with the 'PITCH' key to continuously according to 12 times, such as direct press '4' and '8', xx is a 48, more than 3 seconds to stop flashing, and automatically saved to the counters.Flashing directly press the confirmation key (Enteer) stop flashing, and automatically saved to the project

The meter.

2. Set the set point

Press SET key reset Settings SET characters into 00000 directly according to the setting of the digital keys will shift to the left Such as 00000 to 00002 and then press "2" according to the '8' 00002 to 00028

3. Reset the count value

COUNT the number of real-time COUNT move is expected to take the number changes are, according to the '+' '-'According to "stop/Reset "button2Seconds to loosen,COUNTThe count value into below00000．

4.automatic/Manual mode

After electricity into the main interface shown in the 'A' is the automatic mode, press 'SELECT' key under the main interface after 2 seconds, the main interface will become 'M', 'A' are entered into the manual mode, press "SELECT" under the main interface can be in each other between manual and automatic switching

5.Is the count

Press the 'right' to loosen, in automatic mode (display 'A'), if the SET has SET the value of material plate start right to automatically stop.If there is no tray will automatically stop after started.In manual mode (" M ") until the materials plate since the start.COUNTReal-time display.Less than0Real-time display a negative number.

6.Reverse counting.

Press 'left' loosening in automatic mode (display 'A'), if is SET below the SET value are left to SET data automatically stop.If there is no tray will automatically stop after started.In manual mode (" M ") until the materials plate since the start.COUNTReal-time display.Less than0Real-time display a negative number.

7. Stop counting

Suddenly press the stop button in the motor will stop immediately.

8 PRINT (PRINT) key

In the main screen printing press this button to show the interface, the interface of the first line of the display is a "company name", the second line shows the time, the last line shows the print operation.

After entering the print interface (1), in the third guild has a flashing cursor, the cursor can be modified to edit the content

(2) in according to the 'LEFT/print screenReverse 'can make the cursor move to the left, press'RIGHT/Forward 'can make the cursor to the right.

(3) the print interface is to edit the cursor in the first press the '0', '9' button of a button will show here the Numbers in the button, if short time continuous press the '0', '9' button of a button, display the contents of the can on the buttons to switch between Numbers and letters.The '1' key can be Numbers, special symbols, letters to switch between case and so on

(4) the editor is good after all, the cursor in the field, press "ENTER" key can display 'OK' at the left side of the bank, will keep the content of the bank under the note: save the editing lines must be at the cursor position, in the field and press "ENTER" key to deposit content preserved, for example: if you want to save the first and second lines, must be the cursor in the first row in press 'ENTER' key can keep the contents of the first line, the cursor in the second line "ENTER" button, can put the content of the second row, not save at the same time

(5) in print interface press "SELECT" to enter the parameters of the interface, interface XYWH is shown here:XXX XXX XXX XXX Is to print out the position respectivelyXShaft,YAxis, the width and height.

(6) according to the "stop /Reset "button can return to the main interface

(7) press the "PRINT" button once again and can be printed on the surface of the kumite YinJie content.

Above if any unclear, please contact our 0755-61608823, thank you!

Provide: shenzhen da feng electronic technology co., LTD

The sales /Wang Xinfeng13802269377

Web site:www.szdfk.com